346-0315/02 – Metrology (MET)
Gurantor department | Department of Machining, Assembly and Engineering Metrology | Credits | 4 |
Subject guarantor | Ing. Lenka Čepová, Ph.D. | Subject version guarantor | Ing. Lenka Hřibňáková, Ph.D. |
Study level | undergraduate or graduate | Requirement | Choice-compulsory |
Year | 3 | Semester | summer |
| | Study language | Czech |
Year of introduction | 2004/2005 | Year of cancellation | 2022/2023 |
Intended for the faculties | FMT | Intended for study types | Bachelor |
Subject aims expressed by acquired skills and competences
In this course students are introduced to the basic measurement methods. Virtually try to evaluate the measured data. Passing the course Metrology to increase their skills and acquire the work of many measuring devices. They will also learn to work with data obtained by measurements.
Teaching methods
Lectures
Experimental work in labs
Summary
The subject is connected with lessons form the subjects:„Mathematics,
Technology I, II, and Assembly Technology. The students adopt basic notions
and definitions of metrology, principles of complete measuring data
processing, the determination actual size for determination probability,
measuring methods, distance measurement, angle measuring, evaluation surface
roughness, measuring parts. The theoretical knowledge is practically verified
in the laboratory.
Compulsory literature:
[1] K. J. Hume.Engineering Metrology. London : MacDonald, 1970
[2] Graham T. Smith. Industrial metrology : surfaces and roundness. London :
Springer, 2002
[3] PETŘKOVSKÁ, L.; PETRŮ, J. Engineering Metrology and Assembly. Ostrava : VŠB-Technická univerzita Ostrava, 2012, p. 57.
Recommended literature:
[1] PETŘKOVSKÁ, L.; PETRŮ, J. Engineering Metrology and Assembly. Ostrava : VŠB-Technická univerzita Ostrava, 2012, p. 57.
Way of continuous check of knowledge in the course of semester
Based on the protocol submitted to individual programs and their students are assigned a defense score max. 35 points.
Examination:
Oral part (2 questions), max 30 points / question
One practical question - 5 points.
Total max.65 points total, incl. points per credit up to 100 points
Test questions:
1. The importance of metrology in the system of quality management division.
2. Basic concepts of metrology. Units
3. Law on Metrology as amended by Act 119/2000 Coll (purpose, a division of meters, using measuring instruments, tasks, entities)
4. State metrological control of measuring instruments (gauges type approval, verification and calibration of measuring instruments, certification of reference materials)
5. Following Schemes - the essence, use of
6. Institutions engaged in metrology in the CR, their basic tasks
7. Measurement errors
8. Measurement uncertainty and the expression
9. Gauges with mechanical transmission, optical-mechanical.
10. Meters transfers electrical, pneumatic
11. Metrology length - terminal blocks, use, control
12. Interference of light and its use in metrology
13. Gauges - use their control
14. Metrology plane angle - angle gauges, polygons, ...
15. Checking the conical surfaces - methods, gauge
16. Using trigonometric functions in the control plane angle
17. Control of vertical and horizontal - methods, gauge
18. Checking the threads - Methods, gauges
19. Control Gear - methods, gauge
20. Control of surface roughness - roughness parameters, methods, measuring instruments
21. Requirements for metrology laboratories
E-learning
[1] Tichá, Š.: Strojírenská metrologie část 1, Ostrava : VŠB - TU Ostrava, 2004.
http://www.346.vsb.cz/346.vsb.cz/STROJ%C3%8DRENSK%C3%81%20METROLOGIE-1.d%C3%ADl.pdf
[2] Tichá, Š.: Návody do cvičení z předmětu Strojírenská metrologie. Ostrava : VŠB - TU Ostrava, 2008.
http://www.346.vsb.cz/346.vsb.cz/N%C3%81VODY%20DO%20CVI%C4%8CEN%C3%8D%20Z%20P%C5%98EDM%C4%9ATU%20stroj%C3%ADrensk%C3%A1%20metrologie.pdf
[3] Petřkovská, L., Čepová L. .: Strojírenská metrologie. Ostrava : VŠB-TUO, 2011.
http://www.346.vsb.cz/Petrkovska,%20Cepova%20-%20strojirenska%20metrologie.pdf
Other requirements
Exercise:
Checking the dimensional accuracy of holes
Prerequisities
Subject has no prerequisities.
Co-requisities
Subject has no co-requisities.
Subject syllabus:
Lectures:
In the lectures, students learn about issues that are focused on:
- characteristics of metrology, the definition of important concepts in the field,
- Law on Metrology
- the national metrology system
- measurement errors and uncertainties,
- basic types of meters, gauges principles,
- length metrology, metrology plane angle,
- interference of light, roughness,
- Thread control, control gears,
- Requirements for metrology laboratories.
Exercise:
Checking the dimensional accuracy of holes
Conditions for subject completion
Occurrence in study plans
Occurrence in special blocks
Assessment of instruction