346-5016/02 – Machines and Equipment for Additive Technologies (SZAT)

Gurantor departmentDepartment of Machining, Assembly and Engineering MetrologyCredits4
Subject guarantorIng. Jiří Hajnyš, Ph.D.Subject version guarantorIng. Jiří Hajnyš, Ph.D.
Study levelundergraduate or graduateRequirementCompulsory
Year2Semestersummer
Study languageEnglish
Year of introduction2023/2024Year of cancellation
Intended for the facultiesFSIntended for study typesFollow-up Master
Instruction secured by
LoginNameTuitorTeacher giving lectures
HAJ0058 Ing. Jiří Hajnyš, Ph.D.
JAN0565 Ing. Jan Jansa
MES0011 Ing. Jakub Měsíček, Ph.D.
PAG016 doc. Ing. Marek Pagáč, Ph.D.
Extent of instruction for forms of study
Form of studyWay of compl.Extent
Full-time Graded credit 2+2
Part-time Graded credit 0+16

Subject aims expressed by acquired skills and competences

The aim of the subject is to familiarize students with the design solution of machines and equipment for additive technologies. Students are introduced to several types of 3D printers and finishing equipment. These machines are then analyzed theoretically and practically. After completing the course, the student will be able to perform maintenance and repair of the given printer or device.

Teaching methods

Lectures
Tutorials

Summary

Understanding the functioning of machines and equipment for additive technologies is good preparation for practice. In this subject, the student learns theoretical, but also practical things regarding the construction and operation of 3D printers and their peripherals. Thanks to this, the student is ready to come into practice and thus be ahead of others.

Compulsory literature:

PAGÁČ, M., HAJNYŠ, J., JANČAR, L., MĚSÍČEK, J., JANSA, J. Additive manufacturing. GIBSON, I, D ROSEN a B STUCKER. Additive manufacturing technologies: rapid prototyping to direct digital manufacturing. New York: Springer, c2010, xxii, 459 p. ISBN 1441911200.

Recommended literature:

SCHELLY, Chelsea, Gerald ANZALONE, Bas WIJNEN a Joshua M. PEARCE. Open-source 3-D printing technologies for education: Bringing additive manufacturing to the classroom [online]. 2015, 28, 226-237. ISSN 1045926X. Dostupné z: doi:10.1016/j.jvlc.2015.01.004

Additional study materials

Way of continuous check of knowledge in the course of semester

Project Test Active participation

E-learning

Study materials are shared on lms.vsb.cz.

Other requirements

Knowledge of the subjects Basics of additive technologies and Postprocessing in additive technologies.

Prerequisities

Subject has no prerequisities.

Co-requisities

Subject has no co-requisities.

Subject syllabus:

1. Introduction to machines and equipment for additive technologies 2. The FDM method – the construction of printers and their weak points 3. The FDM method – extruder construction for filament production/recycling 4. The SLM method – the construction of printers and their weak points 5. The SLM method – design and principle of the tumbling device 6. The SLS method – the construction of printers and their weak points 7. The SLS method – construction and principle of the blasting device 8. Assignment of a project 9. The SLA method - construction of printers and their weak points 10. The SLA method – construction and principle of the curing station 11. The DED method – the construction of printers and their weak points 12. The DED method - construction and principle of the electrolytic device 13. Final evaluation of the semester.

Conditions for subject completion

Full-time form (validity from: 2023/2024 Summer semester)
Task nameType of taskMax. number of points
(act. for subtasks)		Min. number of pointsMax. počet pokusů
Graded credit Graded credit 100  51 3
Mandatory attendence participation: In order to complete the credit, students must successfully pass the credit test and submit 1 term paper. Based on the fulfillment of these conditions, they will be awarded a graded credit.

Show history

Conditions for subject completion and attendance at the exercises within ISP: In order to complete the credit, students must successfully pass the credit test and submit 1 term paper. Based on the fulfillment of these conditions, they will be awarded a graded credit.

Show history

Occurrence in study plans

Academic yearProgrammeBranch/spec.Spec.ZaměřeníFormStudy language Tut. centreYearWSType of duty
2025/2026 (N0788A270010) Additive technology ATM P English Ostrava 2 Compulsory study plan
2024/2025 (N0788A270010) Additive technology ATM P English Ostrava 2 Compulsory study plan

Occurrence in special blocks

Block nameAcademic yearForm of studyStudy language YearWSType of blockBlock owner

Assessment of instruction

Předmět neobsahuje žádné hodnocení.