347-0501/02 – Machines Parts and Mechanisms III (ČSIII)

Gurantor departmentDepartment of Machine Parts and MechanismsCredits4
Subject guarantordoc. Ing. Zdeněk Folta, Ph.D.Subject version guarantordoc. Ing. Zdeněk Folta, Ph.D.
Study levelundergraduate or graduateRequirementCompulsory
Year1Semesterwinter
Study languageCzech
Year of introduction2021/2022Year of cancellation
Intended for the facultiesFSIntended for study typesFollow-up Master
Instruction secured by
LoginNameTuitorTeacher giving lectures
FOL20 doc. Ing. Zdeněk Folta, Ph.D.
TRO092 Ing. Miroslav Trochta, Ph.D.
Extent of instruction for forms of study
Form of studyWay of compl.Extent
Full-time Graded credit 1+3
Part-time Graded credit 16+0

Subject aims expressed by acquired skills and competences

Next students knowledge enhancement especially in sphere of transmissions. Variant and comparative evaluation and a design of a drive type.

Teaching methods

Lectures
Tutorials

Summary

Learning outcomes of the course unit The aim of the course is to summarize and extend the knowledge of subjects ČaMS I and ČaMS II. Whole the spectrum of basic machine parts will be applied to the example of the design of the drive of a machine or a mechanism. It will focus on the design of the electric motor or internal combustion engine, optimize the transmission by means of HCR gearing and complement it with other drive elements, especially clutches, bearings and seals. The result will be a semestral project of complex drive.

Compulsory literature:

SHIGLEY, Joseph E. a Charles R. MISCHKE. Mechanical Engineering Design. International 2 Revised ed edition. Europe: McGraw-Hill Education, 1986. ISBN 0-07-100292-8.

Recommended literature:

SHIGLEY, Joseph E. a Charles R. MISCHKE. Mechanical Engineering Design. International 2 Revised ed edition. Europe: McGraw-Hill Education, 1986. ISBN 0-07-100292-8.

Way of continuous check of knowledge in the course of semester

Elaboration of semestral project with individual assignment of calculation parameters and its defense. Final written work.

E-learning

Powerpoint presentations of lectures are available, including design and calculation procedures on http://homel.vsb.cz/~fol20/.

Other requirements

There are no additional requirements.

Prerequisities

Subject has no prerequisities.

Co-requisities

Subject has no co-requisities.

Subject syllabus:

1. Fixed couplings - design, operating coefficient, calculation. 2. Flexible couplings - design, operating coefficient, calculation. 3. Starting, idling and special clutches - design, operating factor, calculation. 4. Spur gearing - geometry. 5. HCR toothing - geometry. 6. Toothing - design calculation and equivalent load. 7. Toothing - strength check and durability. 8. Shaft seals - types of seals, properties and applications. 9. Sliding and rolling bearings - causes and solution of failures. 10. Sliding and rolling bearings - calculation of equivalent load. 11. Sliding and rolling bearings - lifetime calculations, failures. 12. Plastics in construction. Designing in practice. 13. Springs - design and calculation. 14. Adhesives, gluing in designing and service activities.

Conditions for subject completion

Full-time form (validity from: 2021/2022 Winter semester)
Task nameType of taskMax. number of points
(act. for subtasks)
Min. number of points
Graded credit Graded credit 100  51
Mandatory attendence parzicipation: To take part in tutorials to the extent necessary for project elaboration.

Show history

Occurrence in study plans

Academic yearProgrammeField of studySpec.ZaměřeníFormStudy language Tut. centreYearWSType of duty
2021/2022 (NFS0003) Hydraulics and pneumatics P Czech Ostrava 1 Compulsory study plan
2021/2022 (NFS0003) Hydraulics and pneumatics K Czech Ostrava 1 Compulsory study plan

Occurrence in special blocks

Block nameAcademic yearForm of studyStudy language YearWSType of blockBlock owner