717-3730/01 – Simulation of compensation for flexible tools (SKFN)
Gurantor department | Department of Physics | Credits | 4 |
Subject guarantor | prof. Ing. Libor Hlaváč, Ph.D. | Subject version guarantor | prof. Ing. Libor Hlaváč, Ph.D. |
Study level | undergraduate or graduate | Requirement | Choice-compulsory |
Year | 1 | Semester | summer |
| | Study language | Czech |
Year of introduction | 2016/2017 | Year of cancellation | 2018/2019 |
Intended for the faculties | HGF, USP | Intended for study types | Follow-up Master |
Subject aims expressed by acquired skills and competences
Student characterises physical relations leading to the flexible tool trajectory curvature inside material.
Student is able to formulate rules using physical equations that he analyses.
Student predicts parameters of tool necessary for interaction with material.
Teaching methods
Lectures
Seminars
Summary
Cílem předmětu je seznámit studenty s teoretickými i experimentálními způsoby popisu typických rysů zanechaných stopami flexibilních paprsků na materiálu, se způsoby kompenzací a simulacemi těchto kompenzací. Hlavním přínosem by mělo být praktické seznámení se studentů s negativními rysy práce flexibilních nástrojů, naučit se předpovídat jejich velikost podle typu materiálu, jeho rozměrů, rychlosti opracovávání materiálu a dalších faktorů. Student by se měl naučit posoudit, zda bude pro řešení problému vhodný teoretický nebo experimentální přístup, zda je možno potřebnou přesnost dosáhnout použitím kompenzací, nebo je daný flexibilní nástroj pro aplikaci nevhodný z důvodu nemožnosti realizovat požadované zadání, z důvodu enormních nákladů, ekologické zátěže, apod.
Compulsory literature:
Recommended literature:
Hlaváčová, I.M., Hlaváč, L.M., Gembalová, L., Matýsek, D.: Propagation of the abrasive water jet in free air and through material. In: 19th International Conference on Water Jetting, P. Longman (ed.), BHR Group, United Kingdom, 2008, p. 21-30.
ISBN 978-1-85598-104-1
Hlaváč, L.M., Hlaváčová, I.M., Gembalová, L., Kaličinský, J., Fabian, S., Měšťánek, J., Kmec, J., Mádr, V.: Experimental Method for Investigation of the Abrasive Water Jet Cutting Quality. Journal of Materials Processing Technology, (doi:10.1016/j.jmatprotec. 2009.04.011) 209(20), 2009, p. 6190-6195. ISSN 0924-0136
Hlaváč, L.M., Hlaváčová, I.M., Gembalová, L., Jonšta, P.: Experimental investigation of depth dependent kerf width in abrasive water cutting. In: 20th International Conference on Water Jetting, F.H. Trieb (ed.), BHR Group, United Kingdom, 2010, p. 459-467.
ISBN 978-1-85598-121-8
Way of continuous check of knowledge in the course of semester
E-learning
Other requirements
Systematic preparation for lectures.
Prerequisities
Subject has no prerequisities.
Co-requisities
Subject has no co-requisities.
Subject syllabus:
1. Analysis of physical reasons for changes of flexible tool trajectory direction during penetration through material.
2. Physical description of jet trajectory using material and tool properties.
3. Determination of the key parameters influencing trajectory of the given tool type (laser, plasma, liquid jet).
4. Determination of the two basic deviations of the trajectory by penetration of the tool through material – divergence and delay.
5. Determination of the necessary compensations from theoretical models of tool operation.
6. Determination of compensations according to experimental results, determination of typical shapes for calculations of compensations.
7. Analysis of the relation of compensations on machining factors - dynamic modes of changes.
Conditions for subject completion
Occurrence in study plans
Occurrence in special blocks
Assessment of instruction
Předmět neobsahuje žádné hodnocení.